How To Set Pentair Variable Speed Pump

Hello this is Steve Cronin from My Favorite Pool Builder.

Nosotros are a North Florida and Southern Georgia swimming pool Building Visitor. We offer commercial and residential physical pool building and remodeling. We are also a fiberglass swimming pool dealer and installation company. To acme this off, we also offer Eco-finish pool refinishing. If you need to change your physical pool into a pond play pool or take your fiberglass pool and refinish it to brand information technology look like new, we have a solution for you lot.

This is a quick video on how to set your Pentair Intelliflo variable speed variable menstruum pump that were installing at a task.

Understanding the pumps console.

This is the control panel that has a green light that means there'due south ability to the pump. The pump is shut off until the next fourth dimension it should run. I'll show you the panel itself. There are iv buttons beyond the superlative, 1 2 3 and iv. Those buttons are prepare to be used equally push buttons for certain speeds and times. Beneath those are several buttons that serve different functions.

The four buttons on the bottom from left to right.

1. Quick clean which is how you would clean your pool outside of a schedule.
2. Time out and press the service report shut the pump down for predetermined time.
3. Next is the dark-green to red button as your start-finish push. The light-green light to a higher place it will light up when the pump is turned on.
4. Reset would exist there if y'all had an alert and had to reset it for failure, to prime or anything else, this would reset the pump to get-go once again.

See the light above my fingers that's the dark-green light to tell you lot that the pump is powered upwards. You lot can wait to a higher place in the screen and see that we are running a schedule right at present. The schedule is not requiring anything to happen because it's exterior of its time frame. In this example information technology shows that information technology's running on schedule and nothing is currently happening – 0 RPM 0 watts and shows the right fourth dimension above.

Equally you can see number one is selected and the top screen shows a timer, speed is 2550 RPM, it'southward not running yet because it's showing zero watts.

Now speed 2 is selected at 2550 RPM the egg timer shows that 3 hours and 10 minute run-fourth dimension 633 Watts the very bottom shows it is running speed 2.

At present Speed 3 showing 1550 RPMs egg timer showing three hours and 10 minutes 199 watts.

Speed 4 is fix more for our customers. What we do is nosotros set up for an egg timer 2,000 RPM for 10 minutes. This allows us to look at our Period meter that we install on our DE Filter systems to know whether or not the filter needs to be cleaned or backwashed.

This is the menstruation meter that nosotros use. You can see it's xl gallon per minute right now. The pump is gear up at 2000 RPM's for ten minutes. This is how we tell whether or not we need to aftermath and clean the DE filter. If later yous recharge it and if it's all the same dropping down, it'due south time to accept and split the instance and make clean out the cartridges and pleats by themselves.

Programing

Carte du jour

When you printing the bill of fare push the outset affair that comes up is settings, as you lot scroll downwardly through settings you'll run into,

Date and Fourth dimension

Set the appointment and fourth dimension of the pump.

Minimum Maximum

Next is minimum maximum – this is where yous fix the maximum gallons per minute in the menses.
Also the RPM the pump volition run only to avoid over stressing that plumbing.

Device

Adjacent is Device, and then you must set a proper noun of the pump if you're using Automation.

Alarm Log

Next is warning log, this is where we have an issue with the pump shutting downward. Yous would look hither to discover out why it'south shutting down. After you lot reset it the pump should restart.

Program 1 to 8

Next is program one to viii, program one through four are the buttons that yous see in that movie that set up upwards for egg timers, inaugural timers and other timers. Programs five through 8 are disabled.

When you press select from here to drop down the program y'all can choose one through eight to brand and save whatever changes in the schedule or a timer that you choose to exercise.

Program i – Program 1 – iv are virtually the same

Plan 1 on this pump is gear up as an egg timer. If you lot would select this mode right at present and change it to schedule or disabled, once yous are in a department like this, printing Relieve and hitting back.

Speed

Back in selection way, this pump is set up as speed simply you can select this and change from speed to flow or vice versa once you've made your selection printing relieve and hit the back button. Speed and flow piece of work the aforementioned. This is showing speed once you get to that point and hit select, a blackness cursor will pop up on one digit use the right left arrows to movement back and forth. Select the digit and brand the changes that you want to make. To modify the value that you lot're after for example if you desire to alter this from 2550 to 2500 you would hit select Arrow left two times to the five, push the push button downwardly arrow down 5 times and make a zilch, printing save and then hit back.

Egg Timer

Here with the egg timer version of it, yous hit select pointer over to what you want to run. Your fourth dimension default information technology would exist 10 minutes is your hours. Nosotros change our 1 2 and iii a timer for 3 hours and ten minutes.

Program 5-8

I'm skipping the plan five this is where we set up a schedule to really make this pump turn on and turn off.

Arrow down to program 5 and press select to bring upwards schedule, arrow down again allows you lot to choose speed or flow we chose speed. Arrow downwards again and it shows you the speed that is selected. Pointer right or left to get to the number you lot want to brand any changes that yous desire.

Start Time

To relieve your changes when you change your speed it save and back, And then you had a start fourth dimension where we're setting this 1 to start upwardly at vi a.m. in the morning. Get the scroll up or downwards to get to a.m. and p.k. This is how y'all would change it, and so if you lot were at 6 a.grand. you would roll up 12 time to get six p.m. in one case you lot've done that hit save back and now yous're at shut off time.

Close Off Time

Nosotros're setting this one for vii:01 a.m. once you fix your shut off time yous hit save back get to the chief menu by striking back, turn the power off, plough it dorsum on. At this point information technology'due south eleven:45 a.m. on this pump and we set it to run from 6 a.m. to seven:01 a.m.

Plan six

Programme six is the same as five also 7 at 8. Y'all would practice everything the same mode equally we did in five. The only thing I want to show yous is that this 1 matter about time overlap. I tin programme v. You would get through the schedule, downward to speed, change your speed if y'all need to in the speed section, select that and so you lot become to the starting time time with your starting at vii a.grand. Schedule 5 we close downwardly at 7:01 a.1000. the overlap will allow whichever pump speed is higher speed to run for that ane minute just to avoid the pump trying to shut down and restart quickly. Nosotros are setting our close downwards time for 11:01 a.yard. Go on in listen this pool is simply being set up to run temporarily for now but for this sit-in, also the h2o is in the 40-degree marking where right now information technology doesn't really need to run as much. The thermal way is more important.

Features

Thermal Way

Thermal Motors and features and we're going to go through features kind of quick because it's basically works the same mode equally everything else, just toggling upward and down and making the changes that y'all need to make, an end of each individual section

Fourth dimension Out

Timeout used in the feature section to make it where you lot can actually close the pump downwardly for predetermined time say 15 minutes half hour or 60 minutes. And so this allows the technician to make clean the pool filter. I normally hit the stop-get-go and plow the pump off, the danger of that though is its if you forget to plow the pump back on now it'southward not going to run at schedule.

Quick Clean

Quick clean set upward is just similar everything else in the system you lot have to select it, prepare your speed ready your time, and normally set up information technology for 10 hours at the high speed setting of the pump in 2500 2350. It's used to clean the pool when y'all're out of schedule for example yous had a political party in the middle of the night and and then whenever yous're done and you lot want to start the pool cleaning you would hit quick clean and run through the 10 hr plan. Then after that, it would shut off if it's not in schedule. If it was in schedule it would switch to the timed schedule.

Priming

Priming I simply lower the speed that it primes at so it's not revving up so high. I guess it'southward effectually 2,000 RPM.

Thermal mode

So far thermal fashion set up from the factory, you simply desire to check to brand sure it's right and that it's on. Make sure it'southward enabled by going through the menu like nosotros've been doing, check your speed instead of period.

Source: https://www.myfavoritepoolbuilder.com/how-to-set-up-your-pentair-intelliflo-variable-speed-pump/

Share this post